COOLEST HSK/HSN screw condensing unit with BITZER semi-hermetic screw compressor
COOLEST screw condensing unit with open control cabinet
Screw Condensing Units

HSK/HSN Series Bitzer Screw Condensing Units

Screw condensing units on the original German BITZER semi-hermetic screw compressor, for large cooling loads. HSK medium/high 12.5°C to -20°C; HSN low temp -15°C to -45°C. Supplied without condenser, for evaporative or air-cooled condensation. R22/R404A, 380V/3P/50Hz.

Specifications

Compressor
BITZER semi-hermetic screw compressor, original German
Series
HSK medium/high; HSN low temperature
Evaporating temperature
12.5°C to -20°C (HSK); -15°C to -45°C (HSN)
Refrigerant
R22 / R404A
Power supply
380V / 3-phase / 50Hz
Model range
HSK5363-40 to HSK8571-140; HSN5353-25 to HSN8591-160
Cooling capacity, HSK5363-40 at 0°C, R22
97,100 W (catalog sample data)
Cooling capacity, HSK8571-140 at 0°C, R22
340,600 W (catalog sample data)
Cooling capacity, HSN5353-25 at -25°C, R22
33,600 W (catalog sample data)
Condenser
Not included; for evaporative cooling or air-cooled condensation
Dimensions, HSK5363-40
1,800 × 1,250 × 1,350 mm (70.9 × 49.2 × 53.1 in)
Features
No suction/discharge valves; fewer moving parts; economizer for low-temperature efficiency
The HSK/HSN series is COOLEST's screw condensing unit built on the original German BITZER semi-hermetic screw compressor, for large cooling loads. The HSK covers medium/high temperatures from 12.5°C to -20°C; the HSN covers low temperatures from -15°C to -45°C. The unit is supplied without a condenser, for evaporative cooling or air-cooled condensation. It runs on R22 or R404A at 380V/3P/50Hz. If a single piston unit cannot cover the load, start here.
Who the screw unit fits, and who should look elsewhere The screw unit is for buyers whose load has outgrown the piston range. The smallest screw model, the HSK5363-40, delivers 97,100 W at 0°C on R22 (catalog sample data) — roughly where the largest single piston unit ends — and the range runs up to the HSK8571-140 at 340,600 W at the same temperature. Large cold stores, food-processing plants and distribution centres buy screw units when one machine must carry a whole plant. The low-temperature side is covered too: the HSN5353-25 delivers 33,600 W at -25°C on R22, and the HSN range runs down to -45°C, for frozen rooms at a scale piston units do not reach. Two buyers should not start here. If the load fits a single piston unit — anything up to about 124 kW at 0°C — the KLPH or KLPL series is the simpler and smaller machine. And if the site needs a complete unit with its own condenser, note that the screw unit is supplied without one: the condenser — evaporative or air-cooled — is a separate decision, and it belongs in the order. Buy the screw unit when the load demands it, not because it looks like the bigger machine.
What is inside, and how the numbers map to the job The screw compressor works differently from a piston machine, and the catalog says so plainly: no suction or discharge valve plates, which means less vibration and gas pulsation and higher system efficiency; fewer internal moving parts, which means high reliability, long life and less maintenance; and at low temperatures an economizer, which means high efficiency and low running cost. The catalog's own summary is that screw units are especially suitable where a large cooling capacity is required — and the tables bear that out, with single machines from 97 kW to 340 kW at 0°C. Every screw unit leaves the factory with its own standard configuration: BITZER compressor, electric control box, liquid reservoir, oil separator, suction accumulator, filter barrel, sight glass, solenoid valve, pressure controller, high and low pressure gauges, economizer, pipe interface valves, oil cooler and steel frame. The HSK5363-40 measures 1,800 × 1,250 × 1,350 mm with a 60-litre reservoir — this is a large machine, and the plant room must be sized for it. Power is 380V/3P/50Hz and the refrigerant is R22 or R404A across the series. Treat the capacity figures as what they are: catalog sample data for reference. The exact specification of the unit you buy, including the condenser it will work with, is fixed in the contract, not in the catalog.
How to order Ordering a screw unit comes down to five inputs. First, the cooling load — the number that decides whether a screw machine is needed at all. Second, the evaporating temperature: 12.5°C to -20°C for the HSK, or -15°C to -45°C for the HSN. Third, the refrigerant: R22 or R404A. Fourth, the condenser: evaporative cooling or air-cooled condensation, since the unit is supplied without one. Fifth, the power supply on site. With those five, we match the model — from HSK5363-40 up to HSK8571-140, or HSN5353-25 up to HSN8591-160 — and confirm the final specification in the contract. To start, send your cooling load, room temperature and condenser preference through the inquiry form. Yiwu Ruluan Trading will come back with the matching screw model and a quotation. No prices, lead times or certifications are listed on this page because the catalog does not give them; they are confirmed case by case, in writing, before you order.